EMU Working Group K. Hoeper Internet-Draft Motorola, Inc. Intended status: Informational S. Hanna Expires: April 10, 2010 Juniper Networks H. Zhou J. Salowey, Ed. Cisco Systems, Inc. October 7, 2009 Requirements for a Tunnel Based EAP Method draft-ietf-emu-eaptunnel-req-04.txt Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on April 10, 2010. Copyright Notice Hoeper, et al. Expires April 10, 2010 [Page 1] Internet-Draft EAP Tunnel Method Requirements October 2009 Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents in effect on the date of publication of this document (http://trustee.ietf.org/license-info). Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Abstract This memo defines the requirements for a tunnel-based Extensible Authentication Protocol (EAP) Method. This method will use Transport Layer Security (TLS) to establish a secure tunnel. The tunnel will provide support for password authentication, EAP authentication and the transport of additional data for other purposes. Hoeper, et al. Expires April 10, 2010 [Page 2] Internet-Draft EAP Tunnel Method Requirements October 2009 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. Conventions Used In This Document . . . . . . . . . . . . . . 5 3. Use Cases . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1. Password Authentication . . . . . . . . . . . . . . . . . 6 3.2. Protection of Weak EAP Methods . . . . . . . . . . . . . . 6 3.3. Chained EAP Methods . . . . . . . . . . . . . . . . . . . 7 3.4. Identity Protection . . . . . . . . . . . . . . . . . . . 7 3.5. Anonymous Service Access . . . . . . . . . . . . . . . . . 7 3.6. Network Endpoint Assessment . . . . . . . . . . . . . . . 8 3.7. Client Authentication During Tunnel Establishment . . . . 8 3.8. Extensibility . . . . . . . . . . . . . . . . . . . . . . 8 4. Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.1. General Requirements . . . . . . . . . . . . . . . . . . . 9 4.1.1. RFC Compliance . . . . . . . . . . . . . . . . . . . . 9 4.1.2. Draw from Existing Work . . . . . . . . . . . . . . . 9 4.2. Tunnel Requirements . . . . . . . . . . . . . . . . . . . 10 4.2.1. TLS Requirements . . . . . . . . . . . . . . . . . . . 10 4.2.1.1. Cipher Suites . . . . . . . . . . . . . . . . . . 10 4.2.1.1.1. Cipher Suite Negotiation . . . . . . . . . . . 10 4.2.1.1.2. Tunnel Data Protection Algorithms . . . . . . 11 4.2.1.1.3. Tunnel Authentication and Key Establishment . 11 4.2.1.2. Tunnel Replay Protection . . . . . . . . . . . . . 11 4.2.1.3. TLS Extensions . . . . . . . . . . . . . . . . . . 11 4.2.1.4. Peer Identity Privacy . . . . . . . . . . . . . . 12 4.2.1.5. Session Resumption . . . . . . . . . . . . . . . . 12 4.2.2. Fragmentation . . . . . . . . . . . . . . . . . . . . 12 4.2.3. Protection of Data External to Tunnel . . . . . . . . 12 4.3. Tunnel Payload Requirements . . . . . . . . . . . . . . . 12 4.3.1. Extensible Attribute Types . . . . . . . . . . . . . . 13 4.3.2. Request/Challenge Response Operation . . . . . . . . . 13 4.3.3. Mandatory and Optional Attributes . . . . . . . . . . 13 4.3.4. Vendor Specific Support . . . . . . . . . . . . . . . 13 4.3.5. Result Indication . . . . . . . . . . . . . . . . . . 13 4.3.6. Internationalization of Display Strings . . . . . . . 14 4.4. EAP Channel Binding Requirements . . . . . . . . . . . . . 14 4.5. Requirements Associated with Carrying Username and Passwords . . . . . . . . . . . . . . . . . . . . . . . . 14 4.5.1. Security . . . . . . . . . . . . . . . . . . . . . . . 14 4.5.1.1. Confidentiality and Integrity . . . . . . . . . . 14 4.5.1.2. Authentication of Server . . . . . . . . . . . . . 14 4.5.1.3. Server Certificate Revocation Checking . . . . . . 15 4.5.2. Internationalization . . . . . . . . . . . . . . . . . 15 4.5.3. Meta-data . . . . . . . . . . . . . . . . . . . . . . 15 Hoeper, et al. Expires April 10, 2010 [Page 3] Internet-Draft EAP Tunnel Method Requirements October 2009 4.5.4. Password Change . . . . . . . . . . . . . . . . . . . 15 4.6. Requirements Associated with Carrying EAP Methods . . . . 16 4.6.1. Method Negotiation . . . . . . . . . . . . . . . . . . 16 4.6.2. Chained Methods . . . . . . . . . . . . . . . . . . . 16 4.6.3. Cryptographic Binding with the TLS Tunnel . . . . . . 16 4.6.4. Peer Initiated . . . . . . . . . . . . . . . . . . . . 17 4.6.5. Method Meta-data . . . . . . . . . . . . . . . . . . . 17 5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 18 6. Security Considerations . . . . . . . . . . . . . . . . . . . 18 6.1. Cipher Suite Selection . . . . . . . . . . . . . . . . . . 18 6.2. Tunneled Authentication . . . . . . . . . . . . . . . . . 19 6.3. Data External to Tunnel . . . . . . . . . . . . . . . . . 19 6.4. Separation of TLS Tunnel and Inner Authentication Termination . . . . . . . . . . . . . . . . . . . . . . . 19 7. References . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7.1. Normative References . . . . . . . . . . . . . . . . . . . 20 7.2. Informative References . . . . . . . . . . . . . . . . . . 21 Appendix A. Changes from -01 . . . . . . . . . . . . . . . . . . 22 Appendix B. Changes from -02 . . . . . . . . . . . . . . . . . . 23 Appendix C. changes from -03 . . . . . . . . . . . . . . . . . . 23 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 23 Hoeper, et al. Expires April 10, 2010 [Page 4] Internet-Draft EAP Tunnel Method Requirements October 2009 1. Introduction Running EAP methods within a TLS protected tunnel has been deployed in several different solutions. EAP methods supporting this include PEAP [PEAP], TTLS [RFC5281] and EAP-FAST [RFC4851]. In general this has worked well so there is consensus to continue to use TLS as the basis for a tunnel method. There have been various reasons for employing a protected tunnel for EAP processes. They include protecting weak authentication exchanges, such as username and password. In addition a protected tunnel can provide means to provide peer identity protection and EAP method chaining. Finally, systems have found it useful to transport additional types of data within the protected tunnel. This document describes the requirements for an EAP tunnel method as well as for a password protocol supporting legacy password verification within the tunnel method. 2. Conventions Used In This Document Use of each capitalized word within a sentence or phrase carries the following meaning during the EMU WG's method selection process: MUST - indicates an absolute requirement MUST NOT - indicates something absolutely prohibited SHOULD - indicates a strong recommendation of a desired result SHOULD NOT - indicates a strong recommendation against a result MAY - indicates a willingness to allow an optional outcome Lower case uses of "MUST", "MUST NOT", "SHOULD", "SHOULD NOT" and "MAY" carry their normal meaning and are not subject to these definitions. 3. Use Cases To motivate and explain the requirements in this document, a representative set of use cases for the EAP tunnel method are supplied here. The candidate tunnel method is expected to support all of the use cases marked as MUST. Hoeper, et al. Expires April 10, 2010 [Page 5] Internet-Draft EAP Tunnel Method Requirements October 2009 3.1. Password Authentication Many legacy systems only support user authentication with passwords. Some of these systems require transport of the actual username and password to the authentication server. This is true for systems where the authentication server does not have access to the cleartext password or a consistent transform of the cleartext password. Example of such systems are one time password (OTP) systems and other systems where the username and password are submitted to an external party for validation. The tunnel method MUST support transporting username and password to the authentication server. However, it MUST NOT expose the username and password to parties in the communication path between the peer and the EAP Server and it MUST provide protection against man-in-the-middle and dictionary attacks. The combination of the tunnel authentication and password authentication MUST enable mutual authentication. Since EAP authentication occurs before network access is granted the tunnel method SHOULD enable an inner exchange to provide support for minimal password management tasks including password change, "new PIN mode", and "next token mode" required by some systems. 3.2. Protection of Weak EAP Methods Some existing EAP methods have vulnerabilities that could be eliminated or reduced by running them inside a protected tunnel. For example, a method such as EAP-MD5 does not provide mutual authentication or protection from dictionary attacks. Without extra protection, tunnel-based EAP methods are vulnerable to a special type of tunnel man-in-the-middle attack [TUNNEL-MITM]. This attack is referred to as "tunnel MitM attack" in the remainder of this document. The additional protection needed to thwart tunnel MitM attacks depends on the inner method executed within the tunnel. In particular, when weak methods are used, security policies enforcing that such methods can only be executed inside a tunnel but never outside one are required to mitigate the attack. On the other hand, a technical solution (so-called cryptographic bindings) can be used whenever the inner method is not susceptible to attacks outside a tunnel and derives keying material. Only the latter mitigation technique can be made an actual requirement for tunnel-based EAP methods (see Section 4.6.3), while security policies are outside the scope of this requirement draft. Please refer to the NIST Recommendation for EAP Methods Used in Wireless Network Access Authentication [NIST SP 800-120] for a discussion on security policies and complete solutions for thwarting tunnel MitM attacks. The tunnel method MUST support protection of weak EAP methods. Cryptographic protection from tunnel MitM attacks MUST be provided Hoeper, et al. Expires April 10, 2010 [Page 6] Internet-Draft EAP Tunnel Method Requirements October 2009 for all key generating methods. In combination with an appropriate security policy this will thwart MitM attacks against inner methods. 3.3. Chained EAP Methods Several circumstances are best addressed by using chained EAP methods. For example, it may be desirable to authenticate the user and also authenticate the device that he or she is using. However, chained EAP methods from different conversations can be re-directed into the same conversation by an attacker giving the authenticator the impression that both conversations terminate at the same end- point. Cryptographic binding can be used to bind the results of key generating methods together or to an encompassing tunnel. The tunnel method MUST support chained EAP methods while including strong protection against attacks on method chaining. 3.4. Identity Protection When performing an EAP authentication, the peer may want to protect its identity, only disclosing its identity to a trusted backend authentication server. This helps to maintain the privacy of the peer's identity. The tunnel method MUST support identity protection, ensuring that peer identity is not disclosed to the authenticator and any other intermediaries before the server that terminates the tunnel method. Peer identity protection provided by the tunnel method applies to tunnel method and inner method specific identities. Note that the peer may need to expose the realm portion of the EAP outer identity in the NAI [RFC4282] in a roaming scenario in order to reach the appropriate authentication server. 3.5. Anonymous Service Access When network service is provided, it is sometimes desirable for any user to be able to gain access to the network to enable access to limited services emergency communication or troubleshooting information. To avoid eavesdropping, it's best to negotiate link layer security as with any other authentication. Therefore, the tunnel method SHOULD allow anonymous peers or server- only authentication, but still derive keys that can be used for link layer security. The tunnel method MAY also allow for the bypass of server authentication processing on the client. Forgoing authentication increases the chance of man-in-the-middle and other types of attacks that can compromise the derived keys used for link layer security. In addition, passwords and other sensitive Hoeper, et al. Expires April 10, 2010 [Page 7] Internet-Draft EAP Tunnel Method Requirements October 2009 information must not be disclosed to an unauthenticated or unauthorized server. 3.6. Network Endpoint Assessment The Network Endpoint Assessment (NEA) protocols and reference model described in [RFC5209] provide a standard way to check the health ("posture") of a device at or after the time it connects to a network. If the device does not comply with the network's requirements, it can be denied access to the network or granted limited access to remediate itself. EAP is a convenient place for conducting an NEA exchange. The tunnel method SHOULD support carrying NEA protocols such as PB- TNC [I-D.ietf-nea-pb-tnc]. Depending on the specifics of the tunnel method, these protocols may be required to be carried in an EAP method. 3.7. Client Authentication During Tunnel Establishment In some cases the peer will have credentials usable to authenticate during tunnel establishment. These credentials may only partially authenticate the identity of the peer and additional authentication may be required inside the tunnel. If the identity of the peer is fully authenticated during tunnel establishment then the tunnel may be used to communicate additional data. The tunnel method MUST be capable of providing client side authentication during tunnel establishment. 3.8. Extensibility The tunnel method MUST provide extensibility so that additional data related to authentication, authorization and network access can be carried inside the tunnel in the future. This removes the need to develop new tunneling methods for specific purposes. One example of a application for extensibility is credential provisioning. When a peer has authenticated with EAP, this is a convenient time to distribute credentials to that peer that may be used for later authentication exchanges. For example, the authentication server can provide a private key or shared key to the peer that can be used by the peer to perform rapid re-authentication or roaming. In addition there have been proposals to perform enrollment within EAP, such as [I-D.mahy-eap-enrollment]. Another use for extensibility is support for authentication frameworks other than EAP. Hoeper, et al. Expires April 10, 2010 [Page 8] Internet-Draft EAP Tunnel Method Requirements October 2009 4. Requirements 4.1. General Requirements 4.1.1. RFC Compliance The tunnel method MUST include a Security Claims section with all security claims specified in Section 7.2 in RFC 3748 [RFC3748]. In addition, it MUST meet the requirement in Sections 2.1 and 7.4 of RFC 3748 that tunnel methods MUST support protection against man-in-the- middle attacks. Furthermore, the tunnel method MUST support identity protection as specified in Section 7.3 in RFC 3748. The tunnel method MUST be unconditionally compliant with RFC 4017 [RFC4017] (using the definition of "unconditionally compliant" contained in section 1.1 of RFC 4017). This means that the method MUST satisfy all the MUST, MUST NOT, SHOULD, and SHOULD NOT requirements in RFC 4017. The tunnel method MUST meet all the MUST and SHOULD requirements relevant to EAP methods contained in the EAP Key Management Framework [RFC5247] or its successor. This includes the generation of the MSK, EMSK, Peer-Id, Server-Id and Session-Id. This will enable the tunnel method to properly fit into the EAP key management framework, maintaining all of the security properties and guarantees of that framework. The tunnel method MUST NOT be tied to any single cryptographic algorithm. Instead, it MUST support run-time negotiation to select among an extensible set of cryptographic algorithms. This includes algorithms used with certificates presented during tunnel establishment. This "cryptographic algorithm agility" provides several advantages. Most important, when a weakness in an algorithm is discovered or increased processing power overtakes an algorithm, users can easily transition to a new algorithm. Also, users can choose the algorithm that best meets their needs. The tunnel method MUST meet the SHOULD and MUST requirements pertinent to EAP method contained in Section 3 of RFC 4962 [RFC4962]. This includes: cryptographic algorithm independence; strong, fresh session keys; replay detection; keying material confidentiality and integrity; and confirmation of cipher suite selection. 4.1.2. Draw from Existing Work Several existing tunnel methods are already in widespread usage: EAP- FAST [RFC4851], EAP-TTLS [RFC5281], and PEAP. Considerable experience has been gained from various deployments with these Hoeper, et al. Expires April 10, 2010 [Page 9] Internet-Draft EAP Tunnel Method Requirements October 2009 methods. This experience SHOULD be considered when evaluating tunnel methods. If one of these existing tunnel methods can meet the requirements contained in this specification then that method SHOULD be preferred over a new method. Even if minor modifications or extensions to an existing tunnel method are needed, this method SHOULD be preferred over a completely new method so that the advantage of accumulated deployment experience and security analysis can be gained. 4.2. Tunnel Requirements The following section discusses requirements for TLS Tunnel Establishment. 4.2.1. TLS Requirements The tunnel based method MUST support TLS version 1.2 [RFC5246] and may support earlier versions to enable the possibility of backwards compatibility. The following section discusses requirements for TLS Tunnel Establishment. 4.2.1.1. Cipher Suites 4.2.1.1.1. Cipher Suite Negotiation Cipher suite negotiations always suffer from downgrading attacks when they are not secured by any kind of integrity protection. A common practice is a post integrity check in which, as soon as available, the established keys (here the tunnel key) are used to derive integrity keys. These integrity keys are then used by peer and authentication server to verify whether the cipher suite negotiation has been maliciously altered by another party. Integrity checks prevent downgrading attacks only if the derived integrity keys and the employed integrity algorithms cannot be broken in real-time. See Section 6.1 or [KHLC07] for more information on this. Hence, the tunnel method MUST provide integrity protected cipher suite negotiation with secure integrity algorithms and integrity keys. All versions of TLS meet these requirements as long as the cipher suites used provide strong authentication, key establishment and data integrity protection. Hoeper, et al. Expires April 10, 2010 [Page 10] Internet-Draft EAP Tunnel Method Requirements October 2009 4.2.1.1.2. Tunnel Data Protection Algorithms In order to prevent attacks on the cryptographic algorithms employed by inner authentication methods, a tunnel protocol's protection needs to provide a basic level of algorithm strength. The tunnel method MUST provide at least one mandatory to implement cipher suite that provides the equivalent security of 128-bit AES for encryption and message authentication. See Part 1 of the NIST Recommendation for Key Management [NIST SP 800-57] for a discussion of the relative strengths of common algorithms. 4.2.1.1.3. Tunnel Authentication and Key Establishment A tunnel method MUST provide unidirectional authentication from authentication server to EAP peer and mutual authentication between authentication server and EAP peer. The tunnel method MUST provide at least one mandatory to implement cipher suite that provides certificate-based authentication of the server and provides optional certificate-based authentication of the client. Other types of authentication MAY be supported. At least one mandatory to implement cipher suite MUST be approved by NIST DRAFT Recommendation for Key Management, Part 3 [NIST SP 800-57p3], i.e., the ciphersuite MUST be listed in Table 4-1, 4-2 or 4-3 in that document. The mandatory to implement cipher suites MUST NOT include "export strength" cipher suites, cipher suites providing mutually anonymous authentication or static Diffie-Hellman cipher suites. Other ciphersuites MAY be selected following the security requirements for tunnel protocols in NIST DRAFT Recommendation for EAP Methods Used in Wireless Network Access Authentication [NIST SP 800-120]. 4.2.1.2. Tunnel Replay Protection In order to prevent replay attacks on a tunnel protocol, the message authentication MUST be generated using a time-variant input such as timestamps, sequence numbers, nonces, or a combination of these so that any re-use of the authentication data can be detected as invalid. TLS makes use of an 8 byte sequence number to protect against replay. 4.2.1.3. TLS Extensions In order to meet the requirements in this document TLS extensions MAY be used. For example, TLS extensions may be useful in providing Hoeper, et al. Expires April 10, 2010 [Page 11] Internet-Draft EAP Tunnel Method Requirements October 2009 certificate revocation information via the TLS OCSP extension (thus meeting the requirement in Section 4.5.1.3). 4.2.1.4. Peer Identity Privacy A tunnel protocol MUST support peer privacy. This requires that the username and other attributes associated with the peer are not transmitted in the clear or to an unauthenticated, unauthorized party. Peer identity protection provided by the tunnel method applies to tunnel methods and inner method specific identities. If applicable, the peer certificate is sent confidentially (i.e. encrypted). 4.2.1.5. Session Resumption The tunnel method MUST support TLS session resumption as defined in [RFC5246]. The tunnel method MAY support other methods of session resumption such as those defined in [RFC5077]. 4.2.2. Fragmentation Tunnel establishment sometimes requires the exchange of information that exceeds what can be carried in a single EAP message. In addition information carried within the tunnel may also exceed this limit. Therefore a tunnel method MUST support fragmentation and reassembly. 4.2.3. Protection of Data External to Tunnel An attacker in the middle can modify clear text values such as protocol version and type code information communicated outside the TLS tunnel. The tunnel method MUST provide implicit or explicit protection of the protocol version and type code. If modification of other information external to the tunnel can cause exploitable vulnerabilities, the tunnel method MUST provide protection against modification of this additional data. 4.3. Tunnel Payload Requirements This section describes the payload requirements inside the tunnel. These requirements frequently express features that a candidate protocol must be capable of offering so that a deployer can decide whether to make use of that feature. This section does not state requirements about what features of each protocol must be used during a deployment. Hoeper, et al. Expires April 10, 2010 [Page 12] Internet-Draft EAP Tunnel Method Requirements October 2009 4.3.1. Extensible Attribute Types The payload MUST be extensible. Some standard payload attribute types will be defined to meet known requirements listed below, such as password authentication, inner EAP method, vendor specific attributes, and result indication. Additional payload attributes MAY be defined in the future to support additional features and data types. 4.3.2. Request/Challenge Response Operation The payload MUST support request and response type of half-duplex operation typical of EAP. Multiple attributes may be sent in a single payload. The payload MAY support carrying on multiple authentications in a single payload packet. 4.3.3. Mandatory and Optional Attributes The payload MUST support marking of mandatory and optional attributes, as well as an attribute used for rejecting mandatory attributes. Mandatory attributes are attributes sent by the requester that the responder is expected to understand and MUST respond to. If the responder does not understand or support one of the mandatory attributes in the request, it MUST ignore the rest of the attributes and send a NAK attribute to decline the request. The NAK attribute MUST support inclusion of which mandatory attribute is not supported. The optional attributes are attributes that are not mandatory to support and respond to. If the responder does not understand or support the optional attributes, it can ignore these attributes. 4.3.4. Vendor Specific Support The payload MUST support communication of an extensible set of vendor-specific attributes. These attributes will be segmented into uniquely identified vendor specific name spaces. They can be used for experiments or vendor specific features. 4.3.5. Result Indication The payload MUST support result indication and its acknowledgement, so both the EAP peer and server will end up with a synchronized state. The result indication is needed after each chained inner authentication method and at the end of the authentication, so separate result indication for intermediate and final result MUST be supported. Hoeper, et al. Expires April 10, 2010 [Page 13] Internet-Draft EAP Tunnel Method Requirements October 2009 4.3.6. Internationalization of Display Strings The payload MAY provide a standard attribute format that supports international strings. This attribute format MUST support encoding strings in UTF-8 [RFC3629] format. Any strings sent by the server intended for display to the user MUST be sent in UTF-8 format and SHOULD be able to be marked with language information and adapted to the user's language preference as indicated by RFC 4646 [RFC4646]. Note that in some cases, such as when transmitting error codes, it is acceptable to exchange numeric codes that can be translated by the client to support the particular local language. These numeric codes are not subject internationalization during transmission. 4.4. EAP Channel Binding Requirements The tunnel method MUST be capable of meeting EAP channel binding requirements described in [I-D.clancy-emu-chbind]. 4.5. Requirements Associated with Carrying Username and Passwords This section describes the requirements associated with tunneled password authentication. The password authentication mentioned here refers to user or machine authentication using a legacy password database or verifier, such as LDAP, OTP, etc. These typically require the password in its original text form in order to authenticate the peer, hence they require the peer to send the clear text user name and password to the EAP server. 4.5.1. Security Many internal EAP methods have the peer send its password in the clear To the EAP server. Other methods (e.g. challenge-response methods) are vulnerable to attacks if an eavesdropper can intercept the traffic. For any such methods, the security measures in the following sections MUST be met. 4.5.1.1. Confidentiality and Integrity The clear text password exchange MUST be integrity and confidentiality protected. As long as the password exchange occurs inside an authenticated and encrypted tunnel, this requirement is met. 4.5.1.2. Authentication of Server The EAP server MUST be authenticated before the peer can send the clear text password to the server. Hoeper, et al. Expires April 10, 2010 [Page 14] Internet-Draft EAP Tunnel Method Requirements October 2009 4.5.1.3. Server Certificate Revocation Checking In some cases, the EAP peer needs to present its password to the server before it has network access to check the revocation status of the server's credentials. Therefore, the tunnel method MUST support mechanisms to check the revocation status of a credential. The tunnel method SHOULD make use of Online Certificate Status Protocol (OCSP) [RFC2560] or Server-based Certificate Validation Protocol (SCVP) [RFC5055] to obtain the revocation status of the EAP server certificate. 4.5.2. Internationalization The password authentication exchange MUST support user names and passwords in international languages. It MUST support encoding of user name and password strings in UTF-8 [RFC3629] format. The method MUST specify how username and password normalizations and/or comparisons is performed in reference to SASLPrep [RFC4013] or Net- UTF-8 [RFC5198]. Any strings sent by the server intended for display to the user MUST be sent in UTF-8 format and SHOULD be able to be marked with language information and adapted to the user's language preference as indicated by RFC 4646 [RFC4646]. Note that in some cases, such as when transmitting error codes, it is acceptable to exchange numeric codes that can be translated by the client to support the particular local language. These numeric codes are not subject internationalization during transmission. 4.5.3. Meta-data The password authentication exchange SHOULD support additional associated meta-data which can be used to indicate whether the authentication is for a user or a machine. This allows the EAP server and peer to request and negotiate authentication specifically for a user or machine. This is useful in the case of multiple inner authentications where the user and machine both need to be authenticated. 4.5.4. Password Change The password authentication exchange MUST support password change. The exchange SHOULD be extensible to support other "housekeeping" functions, such as the management of PINs or other data, required by some systems. Hoeper, et al. Expires April 10, 2010 [Page 15] Internet-Draft EAP Tunnel Method Requirements October 2009 4.6. Requirements Associated with Carrying EAP Methods The tunnel method MUST be able to carry inner EAP methods without modifying them. EAP methods MUST NOT be redefined inside the tunnel. 4.6.1. Method Negotiation The tunnel method MUST support the protected negotiation of the inner EAP method. It MUST NOT allow the inner EAP method negotiation to be downgraded or manipulated by intermediaries. 4.6.2. Chained Methods The tunnel method SHOULD support the chaining of multiple EAP methods. The tunnel method MUST allow for the communication of intermediate result and verification of compound binding between executed inner methods when chained methods are employed. 4.6.3. Cryptographic Binding with the TLS Tunnel The tunnel method MUST provide a mechanism to bind the tunnel protocol and the inner EAP method. This property is referred to as cryptographic binding. Such bindings are an important tool for mitigating the tunnel MitM attacks on tunnel methods [TUNNEL-MITM]. Cryptographic bindings enable the complete prevention of tunnel MitM attacks without the need of additional security policies as long as the inner method derives keys and is not vulnerable to attacks outside a protected tunnel [KHLC07]. Even though weak or non-key deriving inner methods may be permitted, and thus security policies preventing tunnel MitM attacks are still necessary, the tunnel method MUST provide cryptographic bindings, because only this allows migrating to more secure, policy-independent implementations. Cryptographic bindings are typically achieved by securely mixing the established keying material (say tunnel key TK) from the tunnel protocol with the established keying material (say method key MK) from the inner authentication method(s) in order to derive fresh keying material. If chained EAP methods are executed in the tunnel, all derived inner keys are combined with the tunnel key to create a new compound tunnel key (CTK). In particular, CTK is used to derive the EAP MSK, EMSK and other transient keys (TEK), such as transient encryption keys and integrity protection keys. The key hierarchy for tunnel methods executions that derive compound keys for the purpose of cryptographic binding is depicted in Figure 1. In the case of the sequential executions of n inner methods, a chained compound key CTK_i MUST be computed upon the completion of each inner method i such that it contains the compound key of all Hoeper, et al. Expires April 10, 2010 [Page 16] Internet-Draft EAP Tunnel Method Requirements October 2009 previous inner methods, i.e. CTK_i=f(CTK_i-1, MK_i) with 0 < i <= n and CTK_0=TK, where f() is a good key derivation function, such as one that complies with NIST Recommendation for Key Derivation Using Pseudorandom Functions [NIST SP 800-108]. CTK_n SHOULD serve as the key to derive further keys. Figure 1 depicts the key hierarchy in the case of a single inner method. Transient keys derived from the compound key CTK are used in a cryptographic protocol to verify the integrity of the tunnel and the inner authentication method. ----------- | TK | MK | ----------- | | v v -------- | CTK | -------- | v ---------------- | | | v v v ------- ------ ------- | TEK | | MSK | | EMSK | ------- ------- -------- Figure 1: Compound Keys Furthermore, all compound keys CTK_i and all keys derived from it SHOULD be derived in accordance to the guidelines for key derivations and key hierarchies as specified in Section 4.2.1.1.3. In particular, all derived keys MUST have a lifetime assigned that does not exceed the lifetime of any key higher in the key hierarchy, and MUST prevent domino effects where a compromise in one part of the system leads to compromises in other parts of the system. 4.6.4. Peer Initiated The tunnel method SHOULD allow for the peer to initiate an inner EAP authentication in order to meet its policy requirements for authenticating the server. 4.6.5. Method Meta-data The tunnel method SHOULD allow for the communication of additional data associated with an EAP method. This can be used to indicate whether the authentication is for a user or a machine. This allows the EAP server and peer to request and negotiate authentication Hoeper, et al. Expires April 10, 2010 [Page 17] Internet-Draft EAP Tunnel Method Requirements October 2009 specifically for a user or machine. This is useful in the case of multiple inner EAP authentications where the user and machine both need to be authenticated. 5. IANA Considerations This document has no IANA considerations. 6. Security Considerations A tunnel method is often deployed to provide mutual authentication between EAP Peer and EAP Server and to generate strong key material for use in protecting lower layer protocols. In addition the tunnel is used to protect the communication of additional data, including peer identity between the EAP Peer and EAP Server from disclosure to or modification by an attacker. These sections cover considerations that affect the ability for a method to achieve these goals. 6.1. Cipher Suite Selection TLS supports a wide variety of cipher suites providing a variety of security properties. The selection of strong cipher suites is critical to the security of the tunnel method. Selection of a cipher suite with weak or no authentication, such as an anonymous Diffie- Hellman based cipher suite will greatly increase the risk of system compromise. Since a tunnel method uses the TLS tunnel to transport data, the selection of a ciphersuite with weak data encryption and integrity algorithms will also increase the vulnerability of the method to attacks. A tunnel protocol is prone to downgrading attacks if the tunnel protocol supports any key establishment algorithm that can be broken on-line. In a successful downgrading attack, an adversary breaks the selected "weak" key establishment algorithm and optionally the "weak" authentication algorithm without being detected. Here, "weak" refers to a key establishment algorithm that can be broken in real-time, and an authentication scheme that can be broken off-line, respectively. See [KHLC07] for more details. The requirements in this document disapprove the use of key establishment algorithms that can be broken on-line. Mutually anonymous tunnel protocols are prone to man-in-the-middle attacks described in [KHLC07]. During such an attack, an adversary establishes a tunnel with each the peer and the authentication server, while peer and server believe that they established a tunnel with each other. Once both tunnels have been established, the Hoeper, et al. Expires April 10, 2010 [Page 18] Internet-Draft EAP Tunnel Method Requirements October 2009 adversary can eavesdrop on all communications within the tunnels, i.e. the execution of the inner authentication method(s). Consequently, the adversary can eavesdrop on the identifiers that are exchanged as part of the EAP method and thus, the privacy of peer and/or authentication server is compromised along with any other data transmitted within the tunnels. This document requires server authentication to avoid the risks associated with anonymous cipher suites. 6.2. Tunneled Authentication In many cases a tunnel method provides mutual authentication by authenticating the server during tunnel establishment and authenticating the peer within the tunnel using an EAP method. As described in [TUNNEL-MITM], this mode of operation can allow tunnel man-in-the-middle attackers to authenticate to the server as the peer by tunneling the inner EAP protocol messages to and from a peer executing the method outside a tunnel or with an untrustworthy server. Cryptographic binding between the established keying material from the inner authentication method(s) and the tunnel protocol verifies that the endpoints of the tunnel and the inner authentication method(s) are the same. This can thwart the attack if the inner method derived keys of sufficient strength that they cannot be broken in real-time. In cases where the inner authentication method does not generate any or only weak key material, security policies must be enforced such that the peer cannot execute the inner method with the same credentials outside a protective tunnel or with an untrustworthy server. 6.3. Data External to Tunnel The tunnel method will use data that is outside the TLS tunnel such as the EAP type code or version numbers. If an attacker can compromise the protocol by modifying these values the tunnel method MUST protect this data from modification. In some cases external data may not need additional protection because it is implicitly verified during the protocol operation. 6.4. Separation of TLS Tunnel and Inner Authentication Termination Terminating the inner method at a different location than the outer tunnel needs careful consideration. The inner method data may be vulnerable to modification and eavesdropping between the server that terminates the tunnel and the server that terminates the inner method. For example if a clear text password is used then it may be sent to the inner method server in a RADIUS password attribute which Hoeper, et al. Expires April 10, 2010 [Page 19] Internet-Draft EAP Tunnel Method Requirements October 2009 uses weak encryption that may not be suitable protection for many environments. In some cases terminating the tunnel at a different location may make it difficult for a peer to authenticate the server and trust it for further communication. For example, if the TLS tunnel is terminated by a different organization the peer needs to be able to authenticate and authorize the tunnel server to handle secret credentials that it shares with the home server that terminates the inner method. This may not meet the security policy of many environments." 7. References 7.1. Normative References [I-D.clancy-emu-chbind] Clancy, C. and K. Hoeper, "Channel Binding Support for EAP Methods", draft-clancy-emu-chbind-04 (work in progress), November 2008. [RFC2560] Myers, M., Ankney, R., Malpani, A., Galperin, S., and C. Adams, "X.509 Internet Public Key Infrastructure Online Certificate Status Protocol - OCSP", RFC 2560, June 1999. [RFC3629] Yergeau, F., "UTF-8, a transformation format of ISO 10646", STD 63, RFC 3629, November 2003. [RFC3748] Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J., and H. Levkowetz, "Extensible Authentication Protocol (EAP)", RFC 3748, June 2004. [RFC4017] Stanley, D., Walker, J., and B. Aboba, "Extensible Authentication Protocol (EAP) Method Requirements for Wireless LANs", RFC 4017, March 2005. [RFC4962] Housley, R. and B. Aboba, "Guidance for Authentication, Authorization, and Accounting (AAA) Key Management", BCP 132, RFC 4962, July 2007. [RFC5055] Freeman, T., Housley, R., Malpani, A., Cooper, D., and W. Polk, "Server-Based Certificate Validation Protocol (SCVP)", RFC 5055, December 2007. [RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security (TLS) Protocol Version 1.2", RFC 5246, August 2008. [RFC5247] Aboba, B., Simon, D., and P. Eronen, "Extensible Hoeper, et al. Expires April 10, 2010 [Page 20] Internet-Draft EAP Tunnel Method Requirements October 2009 Authentication Protocol (EAP) Key Management Framework", RFC 5247, August 2008. 7.2. Informative References [I-D.ietf-nea-pb-tnc] Sahita, R., Hanna, S., and K. Narayan, "PB-TNC: A Posture Broker Protocol (PB) Compatible with TNC", draft-ietf-nea-pb-tnc-05 (work in progress), September 2009. [I-D.mahy-eap-enrollment] Mahy, R., "An Extensible Authentication Protocol (EAP) Enrollment Method", draft-mahy-eap-enrollment-01 (work in progress), March 2006. [KHLC07] Hoeper, K. and L. Chen, "Where EAP Security Claims Fail", ICST QShine , August 2007. [NIST SP 800-108] Chen, L., "Recommendation for Key Derivation Using Pseudorandom Functions", Draft NIST Special Publication 800-108, April 2008. [NIST SP 800-120] Hoeper, K. and L. Chen, "Recommendation for EAP Methods Used in Wireless Network Access Authentication", NIST Special Publication 800-120, September 2009. [NIST SP 800-57] Barker, E., Barker, W., Burr, W., Polk, W., and M. Smid, "Recommendation for Key Management - Part 1: General (Revised)", NIST Special Publication 800-57, part 1, March 2007. [NIST SP 800-57p3] Barker, E., Burr, W., Jones, A., Polk, W., , S., and M. Smid, "Recommendation for Key Management, Part 3 Application-Specific Key Management Guidance", Draft NIST Special Publication 800-57,part 3, October 2008. [PEAP] Microsoft Corporation, "[MS-PEAP]: Protected Extensible Authentication Protocol (PEAP) Specification", August 2009. [RFC4013] Zeilenga, K., "SASLprep: Stringprep Profile for User Names and Passwords", RFC 4013, February 2005. Hoeper, et al. Expires April 10, 2010 [Page 21] Internet-Draft EAP Tunnel Method Requirements October 2009 [RFC4282] Aboba, B., Beadles, M., Arkko, J., and P. Eronen, "The Network Access Identifier", RFC 4282, December 2005. [RFC4646] Phillips, A. and M. Davis, "Tags for Identifying Languages", RFC 4646, September 2006. [RFC4851] Cam-Winget, N., McGrew, D., Salowey, J., and H. Zhou, "The Flexible Authentication via Secure Tunneling Extensible Authentication Protocol Method (EAP-FAST)", RFC 4851, May 2007. [RFC5077] Salowey, J., Zhou, H., Eronen, P., and H. Tschofenig, "Transport Layer Security (TLS) Session Resumption without Server-Side State", RFC 5077, January 2008. [RFC5198] Klensin, J. and M. Padlipsky, "Unicode Format for Network Interchange", RFC 5198, March 2008. [RFC5209] Sangster, P., Khosravi, H., Mani, M., Narayan, K., and J. Tardo, "Network Endpoint Assessment (NEA): Overview and Requirements", RFC 5209, June 2008. [RFC5281] Funk, P. and S. Blake-Wilson, "Extensible Authentication Protocol Tunneled Transport Layer Security Authenticated Protocol Version 0 (EAP-TTLSv0)", RFC 5281, August 2008. [TUNNEL-MITM] Asokan, N., Niemi, V., and K. Nyberg, "Man-in-the-Middle in Tunnelled Authentication Protocols", Cryptology ePrint Archive: Report 2002/163, November 2002. Appendix A. Changes from -01 o Added combined mutual authentication in section 3.1 o Changed reference from SP 800-52 to SP 800-57,part 3 o In section 6.2 changed terminology to tunnel MitM and security policy enforcement o Reworded text in section 3.2 to clarify MITM protection o Added more specific text about derivation of the CTK o Removed resource constrained section o Added support for Non EAP authentication as a use for extensibility o Added text to emergency services section to emphasize that sensitive information should not be sent if the server is unauthenticated. o Reworded TLS requirements Hoeper, et al. Expires April 10, 2010 [Page 22] Internet-Draft EAP Tunnel Method Requirements October 2009 o Reworded external data protection requirements o Added text to section 4.6 that states method must not be re- defined inside the tunnel. o Editorial fixes Appendix B. Changes from -02 o Editorial Fixes o Clarified client authentication during tunnel establishment o Changed text so that the tunnel method MUST meet all MUST and SHOULD requirements relevant to EAP methods in RFCs 4962 and 5247 Appendix C. changes from -03 o Resolution of open issues: http://trac.tools.ietf.org/wg/emu/trac/report/9 o Revised section 2 to match other similar RFC(Issue 6) o Cleaned up section 3.2 (issue 8) o Clarified identity protection scope in section 3.4 and 4.2.1.4(issue 9) o Changed Emergency Services to anonymous authentication(section 3.5)(issue 10) o Clarified section 4.1.1 (issue 15) o Cleaned up TLS requirements in section 4.2.1(issue 11) o Replaced text in 4.2.1.1.3 with suitable reference o Improved wording in 4.2.3 and 6.3 (issue 13) o Update internationalization requirements in 4.3.6 and 4.5.2 (Issues 25,18) o Updated text in 4.5.1 (issue 16) o Changed meta-data to SHOULD in 4.5.3 and 4.6.5(Issue 20) o Changed chained methods to SHOULD in 4.6.2(issue 19) o Added security consideration for inner method termination(issue 24) o Updated references o Editorial changes(issues 7,22,17) Authors' Addresses Katrin Hoeper Motorola, Inc. 1301 E Algonquin Rd Schaumburg, IL 60196 USA Email: khoeper@motorola.com Hoeper, et al. Expires April 10, 2010 [Page 23] Internet-Draft EAP Tunnel Method Requirements October 2009 Stephen Hanna Juniper Networks 3 Beverly Road Bedford, MA 01730 USA Email: shanna@juniper.net Hao Zhou Cisco Systems, Inc. 4125 Highlander Parkway Richfield, OH 44286 USA Email: hzhou@cisco.com Joseph Salowey (editor) Cisco Systems, Inc. 2901 3rd. Ave Seattle, WA 98121 USA Email: jsalowey@cisco.com Hoeper, et al. Expires April 10, 2010 [Page 24]